| HOME | HOMELITE PARTS | RYOBI PARTS | OTHER PARTS | GALLERY | EMAIL US |
Prop Hubs : The prop hub (short shaft) has 5/16 x 24 TPI on both the inside (shaft side) and the prop bolt side. It also has heavy anti-slip marks on the front to prevent turning. It comes with the prop hub, turned washer, and prop bolt. (may substituted for a prop shaft) The other type is for the long shaft Homelite engines, comes complete with prop washer and nut. Both are made from 6061 T6 Aluminum
WE CAN MAKE ALL PARTS FOR THE NEW HOMELITE 26CC EXCEPT THE ENGINE MOUNT. MUFFLER IS $30, PROP HUB IS $20
Prop Hub (short shaft) - $20 Long shaft Prop hub - $20
Also available are custom made hubs, 6 bolt prop hubs
1.5 in standoff mount - $20 Homelite Plate Mount - $15
Engine mount: The Homelite engine mount comes in two styles the 1.5 inch and the engine mounted plate. The 1.5 inch adds clearance to permit use of the stock muffler and access to the rear engine bolts. (see the above picture) The engine mount plate is a heavy duty plate that attaches to the rear of the engine. Both mounts include mounting screws and hardware needed.
Velocity Stack - $10
Velocity Stack: This is an item that should be on all carbs that are in the airflow of the plane itself, it helps to keeps the air flowing properly to the venturi of the carb. This stack fits most Homelite engines with a Walbro carb, it can be used on most of the Walbro carbs as well. A larger stack is avalable for larger engines.
Twist type Manifold - $10
Twist type manifold for the Homelite 25/30 engines, now your throttle plate can be horizontal instead of at angle, this new manifold replaces the old one and the carb mounts directly to it.
MACHINED FLYWHEEL - $25 plus $5 shipping (both new and old types)
Flywheel: These are used flywheels that have been machined and balanced and are ready to use on both types of Homelite engines. Your flywheel can be machined and balanced for $30.
25cc Side Dump muffler - $30 25cc Pitts Style muffler - $50
PITTS MUFFLER: The pitts style muffler is available for all of the Homelite engines, now you can have the exhaust in the rear of the engine with this muffler. All mufflers have internal bolt supports
Homelite Conversion Kit Short or Long Shaft Choice of mounts - $40
Kit includes prop hub, velocity stack, mount plate and rotator manifold
Muffler is available for $30
All of the parts shown can be ordered separately, call or email for pricing.
HOMELITE CHAINSAW PARTS:
These parts are larger and stronger than trimmer parts that fit 33/38/45cc HOMELITE Engines
Complete mount set custom fitted to either engine, mount plates and large rail mounts - $35
Large rail mounts are shown below, these mounts can be sold separately $20
Mount plates custom fitted - $20 (all holes drilled complete with bolts)
Blank Mount plates - $10 (no holes or bolts) Prop hub for either engine - $25
Standard Side Dump muffler for Homelite 33/38/45 - $30 All mufflers have bolt supports
(Pipes can be welded or screw in as requested)
Pitts Style Rear Dump muffler for Homelite
33/38/45 - $65
(Pipes are now fully welded but screw in pipes are available
by request)
Below are pictures of the Homelite Chainsaw parts, the first picture is a Homelite mounted with Wackerengines parts and was completed by Don Dresser in his P47 (see modelers pictures)
email for orders and questions is wackerengines@yahoo.com
Phone orders can be placed at 352 287 9662 ( Always happy to answer questions)
NO INTERNATIONALS CALLS PLEASE, USE EMAIL
Mail orders: PETER FAITH PO BOX 4012 HOMOSASSAS SPRINGS FLORIDA 34447
Shipping is priced per item and Area to be shipped ($5 to $6each item max shipping charge) combined orders are priced according to area to be shipped. Canadian Orders are welcome.
